How to Remove Hard Water Stains From Tiles??

Hard Water Stains From Tiles:

Cleaning the floor is never enjoyable, but thankfully, some types of flooring make the process considerably easier. Ceramic tile, in particular, is widely popular because of its minimal maintenance and ease of cleaning. However, some tough stains won’t come out, no matter how hard you scrub.

Housekeeping is like being caught in a revolving door. -Marcelene Cox

Hard water is a concern because it destroys flooring and appliances and discolours tiles and fixtures. The high quantity of calcium and magnesium in water causes water hardness. The build-up of these minerals causes limescale deposits on taps, showerheads, mirrors, and tiles, as well as affecting the correct operation of washing machines, geysers, and dishwashers by blocking pipes and clogging aerators.

The fundamental cause of hard water in India is the dependence on borewell water. As the accumulation of limestone is caused by the mineral content of the water, ordinary cleaners and detergents cannot get rid of it. The most common victim of hard water stains is bathroom tiles as the water accumulates quite frequently over there, and so to answer your question about how to remove hard water stains from bathroom floor tiles & wall tiles, we’ll show some simple methods that you can use.

So, without further ado, let’s dive in and see how to remove/clean hard water stains from tiles-

How To Remove Limescale Stains From Bathroom Tiles??

Vinegar & Baking Soda:

When the two are mixed, molecules exchange, and carbon dioxide bubbles form, lifting and dissolving the mineral deposits. Baking soda’s abrasiveness will also physically dislodge mineral deposits on the grout and tiles.

Step 1: In a large bowl, mix an equal amount of vinegar & baking soda. This mixture will create a mildly abrasive solution that should remove tough stains from tiles easily.

Step 2: Apply the paste to the problematic area and let it rest for up to 10 minutes before scrubbing the tiles and grout with a sponge or brush. Circular movements will assist in loosening the deposit.

Step 3: To remove the paste, thoroughly rinse the entire area with clean water. Finally, use a clean cloth or towel to wipe away any excess water. It is critical to remove any surplus water so that fresh hard water stains do not form.

Vinegar:

Because vinegar is acidic, it is prominent in removing mineral deposits while causing no harm to your tiles.

Step 1: Begin by soaking the problematic region in vinegar, putting a good amount on it. Allow it to soak for 5 minutes before scrubbing with a sponge or brush, and then let it rest for 10 more minutes. You may also use vinegar to soak a cloth and then lay it on the concerned spot.

Step 2: After 10 minutes, rinse the area with clean water. To remove any surplus water, wipe the area with a clean towel.

Hydrochloric Acid:

Because hydrochloric acid is very abrasive, it should be handled with caution. It is preferable to use a commercial product that contains the acid rather than a concentrate since it is less hazardous.

Step 1: First, make sure that your room is well-ventilated and then wear protective gear like gloves, mask, and glasses.

Step 2: Read the label guidelines carefully to ensure you’re using the product correctly. If applied inappropriately, hydrochloric acid can cause grout and tile damage. Dilute it as indicated or spray it straight on the afflicted region if the product is prediluted.

Step 3: Allow the product to sit on the tiles for the specified amount of time before scrubbing with a sponge. Rinse the area well with clean water – this is critical for removing the acid. Finally, use a clean towel to wipe off the tiles and grout.

Things to Avoid:

• Hard bristle or wire brushes, as well as steel wool pads, will harm your tile.
• Chemical cleaners that produce fumes Use them sparingly and operate in a well-ventilated location whenever feasible. Keep children and dogs at bay while you clean.
• Wipe the spill up right away, or they can stain your tile. Always thoroughly dry your floor after cleaning.
• Oil-based cleansers, when used on glazed or glossy tiles, oil-based cleaners create an excessively slippery surface that can lead to accidents.
• Dirt accumulation is a tile floor’s worst enemy. So, clean your tiles regularly.

Looking for how to remove hard water stains from the toilet or shower wall or tiles is easy, but following the steps can be challenging and tiring. Here’s a smart thing you can do to ensure that you never have to look for how to remove tough stains from tiles in the future:

• Preventing hard water stains reduces the amount of time and effort necessary to remove them. After showering or cleaning, rinse the tiles with clean water and wipe them off with a towel or cloth.

The longer minerals remain on a surface, the more difficult it is to remove them, thus it is critical to act early and prevent them from growing at all. Installing a water softener is one of the most common methods of avoiding stains and damage caused by hard water.

The quality of the tiles that you are installing in your home also plays a major role in removing the hard water stains. If your tiles are of bad quality, the scrubbing will leave scratches and will make your floors look dull. So, make sure your tile can handle all the treatments do patch testing on the corner tile. The quality products like that from AGL Tiles will not leave scratches on the floor or any other bathroom fixtures, so make sure to check their products once.

Also, read our blog on various topic like: Beauty, Fashion, Travel and many more.